![offline pages pro manual offline pages pro manual](https://support.unicart.com/wp-content/uploads/2013/11/banktransfer-new.jpg)
- OFFLINE PAGES PRO MANUAL HOW TO
- OFFLINE PAGES PRO MANUAL SOFTWARE
- OFFLINE PAGES PRO MANUAL ISO
- OFFLINE PAGES PRO MANUAL SERIES
Select the data type you would like to delete from the dropdown menu. To delete data from your AFS display, go to Home > Data Management > Delete. Prior to deleting any data from your display, make sure that any data you want to keep has been backed up on another device. From the dropdown menu, select "Tire Radius."
OFFLINE PAGES PRO MANUAL SOFTWARE
What happened to the distance calibration on my combine? Where do I find it?īeginning with version 27 software for Axial Flow combines, the distance calibration is called "Tire Radius." You can find it from the home screen by selecting the "Calibrations" page, then select the "Calibr" tab at the bottom of the screen. Ensure the “AccuGuide enable switch” or “AccuGuide master switch” is in the enabled position.
![offline pages pro manual offline pages pro manual](https://pureinfotech.com/wp-content/uploads/2016/08/xboxone-e203-error-fix.jpg)
How can I fix this?ĪccuGuide is not enabled. I am getting error “AG-060 Cannot engage Automatic” when I attempt to engage AccuGuide on my combine. A TASKDATA folder must be placed on the data card along with your existing *.cn1 folder.
OFFLINE PAGES PRO MANUAL ISO
To use a prescription with an ISO implement, the prescription will need to be written in ISOXML format. If I want to use a prescription for variable rate application, what format should I write it in? I have an ISO implement that I am running with my display. The settings will be dependant on what device you are connecting to and can be obtained from the device manufacturer. Once connected, configure the needed NMEA strings by going to Home > Toolbox > NAV and using the NMEA Output Setup and NMEA Message Setup buttons in the AFS display. The other end of the cable will be connected to the system you are sending GPS to. This cable will plug into the diagnostic connector located on the NAV-II harness. A power/data cable will be required and is available from your dealer (P/N 380002422). The recommended way to output GPS is through the NAV-II controller.
OFFLINE PAGES PRO MANUAL HOW TO
How to I output GPS from my AFS display to another system? To subscribe or renew your subscription for AFS Customer Support, please contact your dealer. How do I subscribe or renew my subscription for for AFS Customer Support? Also make sure that there are no errors (an ERR button above the product or layer box). Make sure that the correct controller is assigned to a layer and a product is assigned to the same layer. Check that your Work Condition setup is correct.If the prescription form and the controller form are not the same, the prescription will not be available for use. For example, when using a prescription for planting, the prescription must be exported as a planting prescription, or when using a prescription for liquid application, the prescription must be exported as a liquid or spraying prescription. The prescription must match the product form of your controller.If there are multiple Growers with the same name, try selecting each individualy to see if the prescription shows under any of them. Go to Home > Performace > Profile and touch in the Grower box. The prescription is only stored under a single Grower/Farm/Field. Next, verify that there are not duplicate Grower/Farm/Field names in the AFS Pro 700 display.When you export a prescription from the desktop software, make sure to backup the existing *.cn1 folder that is on the data card, and then delete the existing *.cn1 folder from the data card before placing the new *.cn1 folder onto the data card. The AFS display will only read a single *.cn1 folder. First, verify that you only have one (1) "*.cn1" folder on the data card.There are multiple reasons why the prescription may not show in your AFS display. Why isn't my prescription showing up in the AFS display?
OFFLINE PAGES PRO MANUAL SERIES
If you are using a 1000 series Raven controller (4000, 4600, etc), use Raven null modem P/N 115-0171-395. If you are using a 100 series Raven controller (440, 460, etc), use Raven null modem P/N 115-0159-822. A Raven null modem cable will need to be sourced from Raven. The power/data cable (P/N 87732647) is available from your Case IH dealer. Please contact your dealer to ensure that the appropriate software is loaded to your AFS display. What do I need to connect a Raven controller to my AFS Display? You can check the versions installed on any CAN device by going to Home > Diagnostics > CAN and finding the device in the list. To check the software versions installed on your AFS display, go to Home > Diagnostics > Version. How do I check what software versions are installed on my AFS display?